CyberPower PowerPanel Manual de usuario descargar pdf (Pagina 2)

2. Time between Power Failure and Initial Warning: This setting determines the delay between when the power fails

and the first audible alarm.

3. Time between Power Failure and Shutdown: This is the user controllable delay between when the power fails and the

software starts the shutdown process. If unchecked, the unit will run on battery until the low battery signal is received (2

minutes of backup time remaining) and then start the shutdown process.

4. Play Voice: Voice is being played when the UPS is turning on or facing a power outage.

5. UPS is Installed On: This shows the current port that the UPS is using. The port assigned to the UPS needs to be used

exclusively for the PowerPanel software.

6. OK: This button is used to exit the setup window and save any changes.

7. Cancel: This button is used to exit the setup window without saving any changes.

8. About: This button will display information about the software, as well as contact information.

PowerPanel Log Window (See Figure 3 )

1. Display Window: This area displays either the Event Log or the Closed Application Information.

2. Event Log: Select this option to view PowerPanel events such as program start, program end, power failure and low battery.

3. Closed Application Information: Select this option to view the file names of applications that were saved by PowerPanel .

Please note: If an application has an existing file name, it will be saved under that file name and not appear in this window.

4. OK: This button is used to exit the log window and save any changes.

5. Cancel: This button is used to exit the log window without saving any changes.

6. Clear: This button is used to clear the information in the selected log.

PowerPanel Shutdown Window (See Figure 4 )

1. Display Window: Any schedule information will be displayed here.

2. Special Setting: This option is used to schedule a shutdown at a specific date and time.

3. Weekly Setting: This option is used to schedule a shutdown for a specific time and day of the week.

4. OK: This button is used to exit the shutdown window and save any changes.

5. Cancel: This button is used to exit the shutdown window without saving any changes.

6. Add: This button is used to add an item to the schedule.

7. Delete: This button is used to delete the selected item.

8. Day, Date and Time: This is the area where you select the day, date and time that you want the shutdown to

occur. Once you have selected it, click the Add Button to add the item to the schedule.

Please note: The use of the schedule is optional and will have no effect on the shutdown of your system during a power failure.

This feature is simply used if you want to have your computer automatically shutdown at a scheduled time.

Using the Windows NT UPS Service

If you are running Windows NT, you may choose to use the Windows NT UPS service instead of

PowerPanel . You can run either PowerPanel or the NT UPS service, but not both.

To configure the Windows NT UPS Service:

1. Click on Start, point to Settings, then Control Panel.

2. Double-click the UPS Icon.

3. Select the COM port that the UPS is connected to.

4. Set the Power Failure Signal to Negative.

5. Set the Low Battery Signal to Negative.

6. Set the Remote UPS Shutdown Signal to Positive.

7. Click OK.

Please note: This service must be stopped in order to use the PowerPanel software. To stop

the service, remove the checkmark from Uninterruptible Power Supply is installed on. Click OK.

Acknowledge the message that the UPS is in an unknown state and exit to the desktop.

2. Double-click on Power Options, and on the UPS Tab, click Select.

3. In the UPS Selection Dialog Box, under Select Manufacturer, select Generic.

4. Under Select Model, select Custom, and on the UPS Tab, click Configure.

5. Set Power Fail / On Battery to Negative.

6. Set Low Battery to Negative.

7. Set UPS Shutdown to Positive, and then Click OK.

Please note: This service must be stopped in order to run PowerPanel . To disable the service, set

the Manufacturer to None.

Please note: You must be logged on as an administrator or a member of the administrator’s group to

make these changes. Network policies may also prevent you from making these changes. Please

contact your network administrator for further assistance.

Using the Windows 2000 UPS Service

If you are running Windows 2000, you may choose to run the Windows 2000 UPS service instead of

PowerPanel . You can run either PowerPanel or the Windows 2000 UPS service, but not both.

To Configure the Windows 2000 UPS Service:

1. Click on Start, point to Settings, then Control Panel.

Testing Your UPS System

Once you have set up your UPS system, you may wish to test it. Make sure that the UPS has been

charged for at least 4 hours before performing this test.

If you are using PowerPanel software:

1. With your UPS and computer on, open an application such as notepad.

2. Enter some data into the application.

3. Unplug the UPS from the AC outlet.

When a power failure occurs, PowerPanel will appear on the screen. The outlet and battery

symbols will change to indicate a power failure. The countdown timer will move towards zero.

When the timer reaches zero, the software will begin to save and close any open applications. The

software will auto-assign names to any files that have not been previously saved, and then save the

file to the C:/PCTemp folder which is located in the root directory of your C drive (where C is the

name of your main hard drive). Once all open files have been saved and closed, PowerPanel will

shutdown the operating system. Once the operating system is shutdown, the UPS will turn off

within 90 seconds. Wait until the UPS has turned off before plugging the UPS back into the outlet.

1. Have your computer and UPS turned on.

2. Unplug the UPS from the wall to simulate a power failure.

3. The UPS will begin beeping, indicating a power failure.

4. Save and close any open files.

5. Shut down the operating system.

6. Once the computer system is shutdown, turn the UPS off.

As the battery discharges, the unit will beep more rapidly, indicating that the battery is nearing

discharge. Once the test is complete, plug the UPS back in and start your computer. Please allow 4

hours for the UPS to recharge before attempting another self-test.

Once the test has been completed, plug the UPS back into the wall and turn it back on. You may then

restart your computer. Please allow 4 hours for the UPS to recharge before attempting another

self-test.

If you are NOT using PowerPanel software:

PowerPanel is a trademark of CyberPower Systems, Inc.

K01-0PP000A

1 2

PowerPanel 1
Testing Your UPS System 2

Comentarios a estos manuales

Sin comentarios

CyberPower PowerPanel Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Unidades De Distribución De Energía (Pdu) CyberPower PowerPanel